LB-2608 Packaging Bag Leak and Seal Positive Pressure Strength Tester (High-Definition Touchscreen)

Product Introduction:

It is suitable for testing the heat-seal strength and seal integrity of various packaging bags and containers. By measuring the material’s heat-seal strength and seal integrity, it enables control and adjustment of key production‑process parameters—such as bag opening characteristics and packaging‑machine speed—thereby ensuring compliance with product‑use requirements.

Reference standard:

GB 10440, GB 18454, GB 19741, GB 17447, ASTM F1140, ASTM F2054, ISO 11607-1, ISO 11607-2, GB/T 17876, GB/T 10004, GB/T 10005, GB/T 17590, BB/T 0003, BB/T 0025, QB/T 1871, YY/T0681, YBB00252005, YBB00162002

Test principle:

1. Leak Test: After reaching the set pressure, maintain the pressure; no additional pressurization is applied during the hold phase. If the pressure drop during the hold period exceeds the specified threshold, the sample is deemed non‑conforming; if the pressure drop remains within the specified threshold, the sample is deemed conforming.
2. Burst test: Once the pressure reaches the threshold, the burst‑detection phase begins; the test stops when the pressure drops to within a specified percentage of the peak pressure, at which point the system automatically releases the air. During this process, the screen displays the recorded maximum pressure value. Pressure is regulated via the pressure‑adjustment valve on the side of the device; it is recommended to increase the pressure gradually to prevent rapid pressurization, which could lead to uneven pressure distribution between the sensor and the sample interior and introduce measurement errors.
3. Pressure Holding/Creep: Once the set pressure is reached, pressure holding begins. During the holding phase, if the pressure drops to (1 − accuracy%) of the set value, a compensating pressure boost is applied to maintain the target pressure. If, during the holding phase, the pressure drop reaches the predefined threshold, the specimen is deemed to have ruptured, the test is terminated, and the specimen is classified as non‑conforming.
4. Creep to Burst: After reaching the set pressure, maintain constant pressure. During the hold phase, if the pressure drops to (1 − accuracy%) of the set value, apply a compensating pressure to sustain the target level. If the pressure drop during the hold phase reaches the predefined threshold, the test is deemed to have reached burst; pressure holding is then terminated, timing stops, and the counter is not reset.
5. Large‑scale leakage: Use a dedicated clamping fixture to press the bag underwater, inflate the test bag to a specified pressure, and visually inspect for leaks. The test duration is manually controlled and can be stopped by pressing the stop button.

Product Features:

1. Intelligent control enables one‑button operation for pressurization, pressure maintenance, timing, and pressure relief during testing, resulting in high test efficiency.
2. The test range is customizable, offering a wide measurement span and broad application versatility.
3. Dual test method for swelling inhibition and non‑swelling inhibition
4. Supports test attachments, offers flexible test modes, and ensures broad compatibility.
5. It employs imported SMC pneumatic components, ensuring durable performance and stable, reliable operation.

Technical Specifications:

Structural features (Wiring and piping methods when using an air compressor as the air source):

Interface Overview:

1 Test Homepage

Start: Begin the experiment;

Breaking the Void: Manually break the void;

Stop: Stop the current experiment;

Save: Save the current experimental data;

Print: Print test data via the built-in printer;

2 Test Plan:

Click “Test Plan” to enter the test plan configuration interface.

Select the desired test function and configure the corresponding parameters for each test.

Trial Name: You can enter the sample product name.

Unit Selection: This instrument supports four unit options: kPa, MPa, bar, and psi.

Test pressure: The specified test pressure is maintained within the tolerance range of the set value.

Test time: The specified test duration, in seconds; maximum value: 9,999,999 seconds, approximately 2,770 hours.

Threshold: Similarly, to prevent false judgments caused by pressure fluctuations, a minimum burst pressure threshold is set for the specimen; only pressure variations exceeding this threshold are deemed valid bursts.

Holding time: Pressure hold time, in seconds (s), with a maximum of 9,999,999 s, equivalent to approximately 2,770 hours.

Sensitivity: Only pressure changes exceeding this set threshold are considered valid burst events; this threshold should be appropriately configured to avoid false alarms caused by pressure fluctuations.

3 Historical Data:

Click “Historical Data” to access the historical data query interface.

Next: Scroll down to view the next record in sequence.

Previous: Starting from the second record, clicking “Previous” allows you to view the preceding record.

Single-item printing: Printed out via the built-in printer, one record per print job.

Delete: Delete data, printing one record at a time.

4 Settings:

Click “Settings” to enter the parameter configuration interface.

4.1 Default Settings:

Storage: Selecting “Automatic” means the data will be stored automatically upon completion of the test, while selecting “Manual” means the data will be stored manually.

Eligibility Window: Selecting “Yes” will display a pass/fail confirmation window upon completion of the test; selecting “No” will prevent the window from appearing.

Print: Selecting “Automatic” means the test results will be printed automatically upon completion; selecting “Manual” means printing will be performed manually.

Power-on automatic zeroing: Select “On” to reset the current vacuum reading to zero upon startup; select “Off” to display the chamber’s pressure value.

Language: Supports Chinese-English bilingualism

Time setting: In most cases, no calibration is required, as the device is pre‑set at the factory. If you need to make changes, enter the year, month, day, hour, and minute, then press Confirm.

4.2 System Settings – Audit Trail:

Next: Scroll down to view the next record in sequence.

Previous: Starting from the second record, clicking “Previous” allows you to view the preceding record.

4.3 User Management:

Click the “New User” button, and a new user with the username “admin” and password “123456” will appear in the user list. You can modify the username and password by clicking in the dialog box.

After the user is created, click in the permissions list to select and grant the corresponding permissions.

Test steps:

1. Connect the specimen to the fixture and place it inside the sealed container; then close the container lid.
2. Connect the power supply and turn on the switch located on the right rear side of the instrument to power up the device.
3. Enter the “Test Plan” and set the test parameters according to the experimental requirements.
4. After completing the settings, press Return to Home to enter the “Test Home Page”;

Note:

1. Due to the small cavity of the test fixture, gradually increase the flow valve setting to control the rate of pressure rise and prevent pressure overshoot.

2. The instrument automatically controls the pressure and holding time of the test fixture, subjecting the bottle cap to the specified pressure resistance. The user carefully observes whether continuous bubbles emerge at the sealing area of the cap to determine whether the test is合格 (qualified).

4. If you encounter any issues that cannot be resolved during use, please contact technical support promptly at 153-6269-2162.

Shipping List:

Instrument host × 1 unit, sealed container × 1 piece, tooling set × 1 set, air hose × 1 piece, power cord × 1 piece, instruction manual × 1 copy, warranty card and certificate of conformity × 1 copy.